Fretwork is “decoration or patterns or patterns on a floor produced by cutting into or through the top”, in accordance with Merriam-Webster’s Dictionary. But to me, fretwork and scroll sawing, as it is often referred to, is a good method to relieve stress and at the same time get an expression of accomplishment whenever your item is finished. There’s a wide selection of materials that can be utilized for fretwork, including thick paper, a variety of wood materials, soft metals and plastics. Although I have used Plexiglas, plywood and cardboard, my true passion for scroll sawing is wood.
From my viewpoint, the hardest section of using wood is getting the board to a finished thickness and smoothness so the pattern may be attached. https://refityourhome.com/best-scroll-saw-for-beginners/ There are a number of places that you can purchase finished lumber, starting from as thin as 1/8″ Baltic birch and up. When you yourself have the required tools, the absolute most economical way to get going is to buy rough cut lumber from a nearby lumber yard. Rough cut lumber is usually 1″ to 1 1/4″ thick, and most lumberyards will have one edge trim so you can begin out with a straight edge. There are so many beautiful grained hardwoods available, though I primarily use oak, cherry and walnut. Now, the wood is run by way of a band-saw and cut into strips, anywhere from 2″ to 2 1/2″ wide, depending on the original width of the board, so they are fairly uniform in width.
Once cut into strips, the strip is turned on its side and explain to you the band-saw again, cutting it so it’s between ½ and ¾ inches thick. I like to use what they call a re-saw blade in my own band-saw, one that is anywhere from ¼” to ¾” wide. I always be sure that I’ve the guard down as near to the little bit of wood that I could, never wear loose fitting clothes and wear protective eye goggles for safety reasons.
Once most of the strips are cut, they can be glued together, making certain the grain of the wood is alternated to prevent the wood from warping. Then all that’s left is gaining the finishing touches. I run both edges through the joiner to ensure I’ve a flat, straight edge and then through the planer to obtain it down to the desired thickness.
Now I’m almost ready to use the scroll saw. After the pattern is selected, spray art glue is employed to lightly spray the back of the pattern and place it on the finished board. When adhered to the wood, holes are drilled for every place where scroll saw blade access is needed. The clock shown only needed 21 holes drilled, but I have done some designs where over 300 holes were needed. With respect to the scroll saw that you use, it is pretty quick to detach the the top of blade and insert it from the bottom of one’s workpiece so you can commence to cut. Delta includes a handy quick release blade chuck that will also work with various other brands of saws.
One of the nice link between using a scroll saw, is that there surely is very little sanding that needs to be done, mainly on the back and sometimes in the corners, depending how you do them. The blade that you use will even determine simply how much sanding becomes necessary in your inner cuts. My preference could be the Olson Double-Tooth, Skipped Tooth blade; it seems to keep only a little cooler which means it lasts only a little longer. One thing you don’t want to use is a dreary blade, as it is really hard to keep in your lines with a dreary blade, and sometimes you don’t have lots of room for veering off lines. After the piece is sanded to your satisfaction and glued together, all that is left if gaining the finish. I choose the natural grain and color of the wood, so I usually work with a semi-clear gloss coating, which really enhances the natural grain.
It is really great to start out with a piece of rough cut lumber and end up getting a keepsake. I demonstrated the scroll saw for A-Line Machine and Tool at some workshops they’d on woodworking, and discovered this hobby is enjoyed by all ages. Kids as young as 9 years of age and up to 90 years of age came in and wanted some tips on scroll sawing. There are always a lot of personal preferences in regards to scroll sawing, including the device and blades used, cuts of wood or kinds of materials, or what finish is applied to their art. But most people who check it out once, love utilizing the scroll saw.